How much does it cost to replace a broken sprinkler head in Dallas?, Complete Guide

A broken sprinkler head replacement in Dallas typically runs $65-$150 per head installed. Dallas Green Sprinkler Repair prices by head type and count, factoring in the clay-heavy soil across Lakewood, Oak Cliff, and Lake Highlands that can bury or shift risers. Exact price is confirmed on-site.

Sprinkler head replacement cost in Dallas by head type (installed, per head)

How much does it cost to replace a broken sprinkler head in Dallas?

A broken sprinkler head in Dallas costs $65 to $150 per head to replace, installed. The head itself is inexpensive: a standard pop-up spray head part runs $3-$8, and a gear-driven rotor runs $12-$25. Labor is the bulk of the cost. A single spray-head swap on level turf in the M Streets or Casa Linda often finishes in 30-45 minutes. Rotor heads cost more because they cover larger zones, cost more as a part, and require adjusting the arc and radius after install.

Spray heads cost less than rotor heads to replace

Sprinkler head cost splits along two head families. Fixed pop-up spray heads water small areas up to about 15 feet and replace for $65-$95 each. Gear-driven rotor heads throw 15-45 feet across large lawns and replace for $90-$150 each. A single Dallas front yard commonly mixes both: spray heads along the flower beds and rotors on the open turf. Replacing a matched nozzle instead of a whole head can drop the cost to $70-$110 when the pop-up body itself is intact.

Part cost, labor, riser damage, and buried heads drive the final price

Four factors move the number. The part: $3-$8 for a spray head, $12-$25 for a rotor. Labor per head: roughly $40-$70. Riser condition: a head snapped at the threaded riser adds $30-$50 because the broken stub must be extracted from the fitting. Depth: heads buried in packed Dallas clay take longer to excavate. Volume discounts apply when several heads are replaced on the same visit, since the trip fee spreads across the job rather than repeating per head.

A single-head replacement follows a five-step sequence

The work runs in order. First, the technician isolates and shuts off water to the affected zone. Second, the soil around the broken head is dug back to expose the riser. Third, the damaged head unthreads from the riser and any cracked stub is extracted. Fourth, a matching head threads on and the nozzle arc and radius are set to cover the zone without spraying the driveway. Fifth, the zone runs a test cycle and the soil is backfilled. Most single-head jobs finish in under an hour.

One broken head can signal a broken lateral line underneath

A geyser or a head that won't seal sometimes points to more than the head. When water pools around the base or a whole zone loses pressure, the buried lateral line or a seal inside the head may be cracked. A head-plus-lateral-line repair runs $150-$300 or more depending on dig length. Diagnosing this before replacing the head avoids paying for a new head that fails again within days. The nozzle should be inspected for clogging from Dallas hard-water mineral buildup as part of the check.

Freeze damage and hard water are common Dallas failure causes

North Texas sees winter freezes that crack exposed heads and backflow assemblies, plus long summer runtimes that wear gears. Dallas municipal water is hard, so mineral scale clogs spray nozzles and stiffens pop-up seals over time. Lawn mowers and edgers are the other frequent culprit, shearing spray heads off at the riser near sidewalk edges. Texas Water Development Board guidance on outdoor water efficiency notes properly adjusted heads cut waste, which matters when a stuck head runs up a city water bill.

Dallas specifics

Dallas sits on expansive clay soil that swells and shrinks with the seasons, shifting buried risers and cracking fittings across Lakewood, Kessler Park, and Preston Hollow. That soil movement is why some head replacements in these neighborhoods run higher than a flat national average. Dallas Water Utilities enforces seasonal watering schedules, and a single stuck or broken head running through a cycle can noticeably raise a monthly bill, so a fast fix pays back. Licensed irrigation work in Texas is regulated by the Texas Commission on Environmental Quality, which oversees irrigator licensing statewide. In older areas like Oak Cliff, the Bishop Arts District, and White Rock, systems can be decades old with brittle risers that snap during a simple head swap, adding riser-extraction time. Our team quotes per head and per zone after seeing the system, and confirms the exact price on a free on-site visit before any digging in Lake Highlands, Vickery Meadow, Casa Linda, or the M Streets.

Related questions

How much does it cost to fix a broken sprinkler valve in Dallas?

A broken sprinkler valve replacement in Dallas typically runs $90-$200 installed, depending on whether the valve is accessible in a box or buried and requires digging.

Why is one sprinkler zone not turning on in Dallas?

A zone that won't turn on usually points to a failed valve solenoid, a controller wiring fault, or a broken wire, diagnosed for a $50-$85 fee often credited toward the repair.

How much does it cost to repair a sprinkler system in Dallas?

A full sprinkler system repair in Dallas ranges from $75 for a single head to $500+ for multiple heads, valves, and line breaks, quoted after an on-site inspection.

How do I fix a sprinkler head that won't pop up in Dallas?

A head that won't pop up is usually clogged with Dallas hard-water scale or dirt, or has a worn seal; cleaning or a $65-$95 head swap resolves most cases.

How long does a sprinkler head replacement take in Dallas?

Most single sprinkler head replacements in Dallas finish in under an hour; multiple heads or a buried riser in clay soil can extend the job.

Call (469) 326-1277 for a free quote